I-DRK-07B ye-DRK-07B yoMvavanyi weNcwadana yokuSebenza yoMvavanyi weFlame Retardant

Isilumkiso sokhuseleko

Basebenzisi abathandekayo

Nceda uqaphele ukuba ezi zinto zilandelayo zinokubandakanyeka kwinkqubo yokusebenzisa isixhobo:

I-1, Nceda uqiniseke ukuba ufunda imigangatho efanelekileyo kunye nemiyalelo yezixhobo ngaphambi kokusebenzisa izixhobo

2、 Ifestile yokujonga kufuneka ivalwe xa uvavanyo luqhubeka!

3, Xa i-voltage echaziweyo isetyenzisiwe, amandla esixhobo kufuneka abekwe phantsi.

4, izinto ezinokutsha neziqhumayo ngaphandle kwezo zifunekayo kuvavanyo zithintelwe ngokungqongqo elabhoratri!

5, Umsebenzisi akayi kushiya indawo yovavanyo.

6, Ilabhoratri iya kuxhotyiswa ngezixhobo zokucima umlilo.

7, Ekupheleni kovavanyo, onke amandla kunye nemithombo yomoya kufuneka icinywe. Nceda qiniseka ukuba ucoce intsalela yovavanyo okanye inkunkuma!

Isishwankathelo

Umhloli we-flame retardant we-respirator uphuhliswa ngokwe-gb2626 izixhobo zokukhusela zokuphefumla, ezisetyenziselwa ukuvavanya ukuxhathisa umlilo kunye nokusebenza kwe-flame retardant ye-respirators. Imigangatho esebenzayo yile: gb2626 amanqaku akhuselayo okuphefumla, iimfuno zobugcisa ze-gb19082 zempahla ekhuselayo yezonyango, i-gb19083 yeemfuno zobugcisa zeemaski zokhuselo lwezonyango, kunye ne-gb32610 iinkcukacha zobuchwephesha zeemaski zokhuselo lwemihla ngemihla Yy0469 imaski yotyando lwezonyango, yyt0969 imaski yonyango elahlayo, njl.

Iiparamitha zobugcisa

1. I-mask head mold yenziwe ngezinto zetsimbi, kwaye iimpawu zobuso zifaniswe ngokomlinganiselo we-1: 1

2. Isikrini sokuchukumisa i-PLC + ulawulo lwe-PLC, ukufezekisa ulawulo / ubhaqo / ukubala / ukubonisa idatha / umbuzo wedatha yembali ngemisebenzi emininzi

3. Isikrini sokuchukumisa:

a. Ubungakanani: 7 "ubungakanani bomboniso obusebenzayo: 15.41cm ubude kunye ne-8.59cm ububanzi;

b. Isigqibo: 480 * 480

c. Ujongano lonxibelelwano: RS232, 3.3V CMOS okanye TTL, imowudi ye-serial port

d. Umthamo wokugcina: 1g

e. Ukusebenzisa i-hardware esulungekileyo ye-FPGA yokubonisa idrayivu, "zero" ixesha lokuqalisa, umbane ungabaleka

f. Isebenzisa i-m3 + FPGA uyilo, i-m3 inoxanduva lokwahlulahlula imiyalelo, iFPGA igxile kumboniso weTFT ukuqinisekisa isantya nokuthembeka.

4. Ubude bokushisa bunokulungiswa

5. Ukuma okuzenzekelayo kunye nexesha

6. Bonisa ixesha emva kokutshisa

7. Ixhotyiswe ngesivamvo somlilo

8. Isantya sokuhamba kwentloko (60 ± 5) mm / s

9. Idayamitha ye-probe yeqondo lokushisa yi-1.5mm

10. Uluhlu lohlengahlengiso lobushushu bomlilo: 750-950 ℃

11. Ukuchaneka kwexesha lokutshisa emva kokutshisa yi-0.1s

12. Ukunikezelwa kwamandla: 220 V, 50 Hz

13. Igesi: ipropane okanye iLPG

Intshayelelo kujongano lokusebenza

Ujongano lovavanyo:

1.Nqakraza ngokuthe ngqo phezulu kwesibane ukulungisa umgama ukusuka kwi-nozzle ukuya kwi-fa ephantsi

2. Qala: umngundo wentloko uqalisa ukuya kwicala le-blowtorch kwaye ume kwenye indawo ngetotshi yokuvuthela.

3. Ukukhupha: vula / cima ifeni yokukhupha ebhokisini →

4. Irhasi: vula / vala umjelo werhasi

5. I-Ignition: qalisa isixhobo sokutshisa uxinzelelo oluphezulu

6. Ukukhanyisa: vula / cima isibane kwibhokisi

7. Gcina: gcina idatha yovavanyo emva kovavanyo

8. Ixesha: rekhoda ixesha lasemva kokutshisa

Uindlela yobulumko

Iingcebiso: nceda ufunde imigangatho yovavanyo efanelekileyo ngononophelo ngaphambi kokusebenzisa izixhobo!

1. Qhagamshela unikezelo lwamandla kunye nomthombo womoya emva kwebhokisi

2. Vula amandla kwaye utyhale iqhosha kwindawo yolawulo yangaphambili (indawo iboniswe kumzobo ongezantsi)

Emva kombane, ngenisa ujongano lovavanyo

a. Okokuqala, cofa iqhosha lohlengahlengiso lwendawo, kwaye isikhunta sentloko siqala ukuhamba. Xa umngundo wentloko uva inzwa yesikhundla somlilo, ukungunda kwentloko kuyeka ukuhamba; ngeli xesha, ulungise ngesandla umgama phakathi kwe-blowtorch kunye nesiphelo esisezantsi semaski ukuya kuma-20 mm, uze ulungise indawo ye-blowtorch.

b. Lungisa indawo yeblowtorch kwaye emva koko ucofe ukuqala ukuseta ngokutsha i-headform

c. Emva kokuba i-head mold isetyenzisiwe, cofa iqhosha legesi ukuvula igesi, kwaye ucinezele iqhosha lokulayita. I-igniter iya kuvutha kathathu. Ukuba ayilayitwanga, cofa iqhosha lokulayita kwakhona

d. khomba isitshisi kwaye ulungelelanise iqhosha lokuhamba kwegesi kwiphaneli ukwenza ukuphakama kwedangatye kube ngama-40 + 4mm.

e. Emva kokulungelelanisa ukuphakama kwedangatye, inzwa yokushisa isetyenziselwa ukulinganisa ubushushu kwi-20 ± 2mm kwi-blowtorch. Iqondo lobushushu ledangatye lihlengahlengiswa ukuya kuma-800 ± 50 ℃ ngokulungelelanisa i-nut kwisiphelo esisezantsi sesitshisi (indawo iboniswe kumzobo ongezantsi) ngomoya.

f. Emva kokulungelelanisa ubushushu, susa inzwa yobushushu, cofa iqhosha lokuqala, kwaye isikhunta sentloko siqala ukuhamba njengesinye isiphelo.

g. Xa i-sensor ye-flame position ibona ukubunjwa kwentloko, ixesha lokutshisa emva kokutshisa ixesha ngokuzenzekelayo. Xa ukuvutha okuqhubekayo (ixesha elipheleleyo lokuvutha kunye nokutsha okungenadanga) kwemaski kucinyiwe, cofa iqhosha lexesha ukumisa ixesha.

h. Unokwenza iipateni ezintathu ngokulandelelanayo, kwaye emva koko ucofe iqhosha elithi Gcina ukugcina idatha

Okunye

1. Idatha egciniweyo inokubuzwa kwidatha yembali

2. Ngexesha lovavanyo, isibane sinokuvulwa okanye sicinywe njengoko kufuneka

3. Emva kovavanyo, vula i-exhaust air ukuze ukhuphe igesi yokutshisa inkunkuma evela kwibhokisi.

4. Ingaba iziphumo zovavanyo zifanelekile zinokuthelekiswa nemigangatho okanye imimiselo efanelekileyo